asebounion.blogg.se - Brocade san switch show ip address

BROCADE SAN SWITCH SHOW IP ADDRESS INSTALL
BROCADE SAN SWITCH SHOW IP ADDRESS ZIP FILE
BROCADE SAN SWITCH SHOW IP ADDRESS ARCHIVE
BROCADE SAN SWITCH SHOW IP ADDRESS PASSWORD
BROCADE SAN SWITCH SHOW IP ADDRESS PC

Follow the ICX 6430 instructions in step 3.Ĭonfigure the Brocade switch to use the Rapid Spanning Tree Protocol (RSTP), which was standardized by IEEE 802.1W.Īfter you perform the following steps, refer to the Brocade ICX 6430 and ICX 6450 Web Configuration QuickStart Guide for additional information about configuring Brocade ICX 6430 switches.

BROCADE SAN SWITCH SHOW IP ADDRESS PC

See the Brocade ICXĦ430 and ICX 6450 Stackable Switches Hardware Installation Guide.īefore you configure the switch, follow steps 1 - 4 in the Brocade ICX 6430 and ICX 6450 Web Management Interface User Guide and the section on Prerequisite Configuration to attach a PC to the switch and assign an IP address to the management port using its Command Line Interface (CLI).

BROCADE SAN SWITCH SHOW IP ADDRESS INSTALL

Scan the IP address of the host where the Brocade Network Advisor is installed. All the FC ports configured in virtual mode will be discovered and associated to the same Network device discovered during the first scan.Use the Brocade documentation to properly install the switch.

FC ports configured in virtual mode will not be discovered at this stage. If the switch is configured and running in Virtual Fabric mode then the switch will be discovered as a Network device.

Scan the IP Address of the Brocade SAN switch. This first scan will discover the Brocade switch as a Network device and all the FC ports using the SANSwitch_FCPorts.tpl pattern.

Create WBEM credentials that have access to the Brocade Network Advisor.

Create SNMP credentials that have access to the Brocade switch.

To discover the Brocade SAN switches running in Virtual Fabric (VF) mode: Once fabrics are added, Brocade Network Advisor automatically discovers the related switches Step 4: Configuring BMC Discovery Enter the fabric information and click OK. Click OK on the Network Advisor Login Banner.ĥ.

BROCADE SAN SWITCH SHOW IP ADDRESS PASSWORD

Enter User ID and Password (by default Administrator and Password) and click Login.Ģ.

If this is not the case, click Start > Programs > Network Advisor xx.x.x > Network Advisor xx.x.xx.ġ. If you followed the two previous steps, the Brocade Network Advisor is automatically launched. The final step to associate the Brocade SAN switches with the Brocade Network Advisor.

Step 3: Working with Brocade Network Advisor Note: For more information, please refer to the Brocade Network Advisor Installation Guide. Once the Network Advisor services are started, the Brocade Network Advisor is displayed. If necessary, select the Start Client check box and click Finish. Verify your configuration information and click Next.ġ0. Configure the SMI Agent and click Next.ĩ. Indicate the Web Server Port # (HTTP), Web Server Port # (HTTPS), Database Port #, Starting Port #, Syslog Port #, SNMP port # and click Next.Ĩ. Configure the server IP and click Next.ħ. Configure the FTP server to be used (internal or external) and click Next.Ħ. Choose the appropriate installation type and click Next.ĥ. Read the Network Advisor Welcome page and click Next.Ĥ. If you selected the Launch Network Advisor Configuration check box during the installation, the following wizard appears:ġ. Make sure the Launch Network Advisor Configuration check box is selected (default) on the Installation Complete screen and click Done. Review the displayed installation summary on the Pre-Installation Summary screen and click Install.ħ. Indicate the Install Folder and click Next.Ħ. Read the agreement on the License Agreement screen, select I accept the terms of the License Agreement, and click Next.ĥ.

BROCADE SAN SWITCH SHOW IP ADDRESS ARCHIVE

Unzip the archive and run the installation file.ģ.

BROCADE SAN SWITCH SHOW IP ADDRESS ZIP FILE

Download the na1120_brocade_windows zip file on the Brocade's website.Ģ. A license will then be required to use this product.ġ. The default Brocade Network Advisor comes as a 75-day evaluation version. The installation files of Brocade Network Advisor 11.2.0 or higher can be downloaded on the Brocade's website, under MyBrocade > Downloads > Product Downloads.

Step 1: Installing Brocade Network Advisor